Wireless Stick(V3)

In order to meet the user’s requirements for high performance and small size, we designed this product. On the basis of WiFi LoRa 32, it’s has a smaller size, 0.49″ OLED display, and better RF characteristics. This product can’t meet your needs? Choose from the Heltec Products Selecter. Over View Datasheet Docs & Resource Wireless…

HT-RA62

The Heltec LoRa Series Module HT-RA62 was designed and developed by Heltec Automation. The module is used for ultra-long-range spread spectrum communication, and its RF chip SX1262 mainly adopts LoRa remote modem for ultra-long-range spread spectrum communication with high interference immunity and low power consumption. With SEMTECH’s patented LoRa modulation technology, the SX1262 has a…

HT-CT62

HT-CT62 is a LoRa/LoRaWAN node module with a long communication range, low power consumption, high sensitivity, and low cost. The module is composed of ESP32-C3FN4 (32-bit microprocessor based on RISC-V architecture) and Semtech LoRa Transceivers (SX1262). The module integrates 2.4 GHz Wi-Fi and LoRa two-mode wireless communication. HT-CT62 is a small volume, stamp hole package…

WIFI LoRa 32 (V3)

WiFi LoRa 32 is a classic IoT dev-board designed & produced by Heltec Automation. Since its launch in 2017, it has been loved by developers and makers. The newly launched V3 version has the same pin sequence as the V2 version and retains Wi-Fi, BLE, LoRa, OLED display, and other functions. It is the best…

Wireless Shell (V3)

HTIT-Wsh (Wireless shell) is a long communication range, high receive sensitivity, low power consumption(9uA), and low-cost LoRa node module. The HTIT-Wsh is composed of an MCU (ESP32-S3FN8) and Semtech LoRa Transceivers (SX1262). 38.4 x 16.1 x 3.2(mm) size with 1.27mm stamp holes package makes it can be assembled into your PCB or products directly. HTIT-Wsh…

CubeCell – Module (V2)

HTCC-AM01 is a Cubecell(TM) Series made by the Heltect team, mainly for LoRa/LoRaWAN node applications. it has the characteristics of long communication range, high receive sensitivity, low power consumption, and low cost. HTCC-AM01 is based on ASR6052, the chip is already integrated with the PSoC® 4000 series MCU (ARM® Cortex® M0+ Core) and SX1262. Regarding…

WiFi Kit 32 (V3)

WiFi kit 32 is a classic IoT Dev-board designed&produced by Heltec Automation(TM), It’s a highly integrated product based on ESP32(including WiFI and BLE), Li-Po battery management system,0.96” OLED are also included. It’s the best choice for smart citites,farms homes,and IoT makers. This product can’t meet your needs? Choose from the Heltec Products Selecter.  Over View…

ESP32-C3

ESP32-C3 is a development board based on the ESP32-C3FN4 chip. ESP32-C3FN4 is a 32-bit microprocessor based on RISC-V architecture. It is a very low-power and high-integration MCU system-level chip (SOC), integrating 2.4 GHz Wi-Fi and low-power Bluetooth (Bluetooth® LE) dual-mode wireless communication. Internal integration 4MB flash, contains SPI, I2C, UART, ADC, etc. It is the…

Wireless Stick Lite (V3)

HTIT-WSL is a development board for Wi-Fi, Bluetooth and LoRa. Because some customers do not need OLED screen when using WiFi Lora32, we launched this product. The HTIT-WSL is composed up of an MCU (ESP32-S3FN8) and Semtech LoRa Transceivers (SX1262), perfectly support Arduino®. Users can easily carry out secondary development and application. This product can’t meet your needs? Choose from the Heltec Products Selecter. Over View Datasheet Docs…

HT-AT62

HT-AT62 is a cost-effective LoRa node module, it has the characteristics of long communication range, high receive sensitivity, low power consumption and low cost. The HT-AT62 is composed of an MCU (32-bit T-Head Microsystems) and Semtech LoRa Transceivers (SX1262). Regarding the software side, it already integrated LoRaWAN 1.0.2 protocol with AT command support. This means that when you use the module, you only need to simply send the corresponding…