CubeCell – Module
$9.90 $8.60
note
accessories
reseller
- This is a module, must work with other PCB board.
- 3.7V/1000mAh lithium(Sale only for mainland China)
- Solar Panel
- Antenna
Related products
-
CubeCell GPS-6502$24.00$19.80 -
CubeCell 1/2AA Node$16.00$12.40 -
CubeCell Dev-Board Plus$18.50$14.40 -
CubeCell - Capsule Sensor $16.30 – $22.00 -
Turtle Board$33.00$29.80 -
Wireless Stick Lite (Panda Board)$18.00$14.90
CubeCell (TM) is a new product series made by Heltec team, mainly for LoRa/LoRaWAN node applications.
CubeCell (TM) series is based on ASR605x (ASR6501, ASR6502), those chips are already integrated with the PSoC® 4000 series MCU (ARM® Cortex® M0+ Core) and SX1262. We have done a lot of migration and development, made it perfectly support Arduino®, can run the LoRaWAN protocol stably, and can easily connect lithium batteries and solar panels.
HTCC-AM01 is a Module. Supports AT transparent transmission commands, can be directly integrated into the application circuit.
Know more about CubeCell series. Or choose from the Heltec LoRa Node family.
HTCC-AM01 is a part of the “CubeCell“ series, with the following features:
- Perfect Arduino-Compatible!
- CE and FCC certification;
- Based on ASR605x (ASR6501, ASR6502), those chips are already integrated the PSoC® 4000 series MCU (ARM® Cortex® M0+ Core) and SX1262;
- LoRaWAN 1.0.2 support;
- Ultra low power design, 3.5uA in deep sleep;
- 1.27 stamp edge design for SMT;
- Good impendence matching and long communication distance.
Technical Parameters
| Source | Parameter | |
| MCU | ASR6501 (48 MHz ARM® Cortex® M0+ MCU, 128KB FLASH, 16KB SRAM ) | |
| LoRa Chip | ASR6501 (Internal assembled Semtech® LoRa® Transceiver SX1262) | |
| LoRa working band | EU_433, CN_470_510, EU_863_870, US_902_928 | |
| LoRa maximum output power | 21dB ± 1dB | |
| Hardware resources | UART x 1; SPI x 1; I2C x 1; SWD x 1 | |
| 12 – bits ADC; 8 – channel DMA engine | ||
| 6 x GPIO | ||
| FLASH | 128KB internal FLASH | |
| Interface | 1.27 x 11 stamp edge x 2;LoRa Antenna (IPEX) x 1 | |
| Size | 18mm x 18mm x 2 mm | |
| Low power design | Deep Sleep 3.5uA | |
Electrical characteristics
| Electrical characteristics | condition | Minimum | Typical | Maximum |
| Power Supply | 3.3V（pin）powered（≥150mA） | 2.7V | 3.3V | 3.5V |
| Power consumption(mA) | LoRa Rx Mode | 10mA | ||
| LoRa 10dBm output | 70mA | |||
| LoRa 14dBm output | 90mA | |||
| LoRa 17dBm output | 100mA | |||
| LoRa 20dBm output | 105mA | |||
| Sleep Mode (3.3V header powered) | 3.5uA |
CubeCell Relevant Document Page
How to install CubeCell Arduino Development Environment
CubeCell Series Source code
Heltec CubeCell series Arduino framework (the basic of CubeCell series products Arduino development environment): https://github.com/HelTecAutomation/ASR650x-Arduino
HTCC-AM01 Pin out Diagram
HTCC-AM01 Recommend Hardware Design
- Recommend schematic diagram
- Schematic and PCB package (Altium Designer)
- AutoCAD size drawing
- 3D module
Heltec LoRa Node Porducts Difference Table (Product Selection Table)
Frequently Asked Questions
Customer Test Report
CubeCell test: https://www.youtube.com/watch?v=lobNwqHLrag
LoRa 470MHz Max Output Power
LoRa 470~510MHz Receiving Status "S Parameters"
Maximum communication distance test
Low power test in sleep mode
- Over View
-
HTCC-AM01 is a part of the “CubeCell“ series, with the following features:
- Perfect Arduino-Compatible!
- CE and FCC certification;
- Based on ASR605x (ASR6501, ASR6502), those chips are already integrated the PSoC® 4000 series MCU (ARM® Cortex® M0+ Core) and SX1262;
- LoRaWAN 1.0.2 support;
- Ultra low power design, 3.5uA in deep sleep;
- 1.27 stamp edge design for SMT;
- Good impendence matching and long communication distance.
- Tech Specs
-
Technical Parameters
Source Parameter MCU ASR6501 (48 MHz ARM® Cortex® M0+ MCU, 128KB FLASH, 16KB SRAM ) LoRa Chip ASR6501 (Internal assembled Semtech® LoRa® Transceiver SX1262) LoRa working band EU_433, CN_470_510, EU_863_870, US_902_928 LoRa maximum output power 21dB ± 1dB Hardware resources UART x 1; SPI x 1; I2C x 1; SWD x 1 12 – bits ADC; 8 – channel DMA engine 6 x GPIO FLASH 128KB internal FLASH Interface 1.27 x 11 stamp edge x 2;LoRa Antenna (IPEX) x 1 Size 18mm x 18mm x 2 mm Low power design Deep Sleep 3.5uA Electrical characteristics
Electrical characteristics condition Minimum Typical Maximum Power Supply 3.3V（pin）powered（≥150mA） 2.7V 3.3V 3.5V Power consumption(mA) LoRa Rx Mode 10mA LoRa 10dBm output 70mA LoRa 14dBm output 90mA LoRa 17dBm output 100mA LoRa 20dBm output 105mA Sleep Mode (3.3V header powered) 3.5uA - Docs & Resource
-
CubeCell Relevant Document Page
How to install CubeCell Arduino Development Environment
CubeCell Series Source code
Heltec CubeCell series Arduino framework (the basic of CubeCell series products Arduino development environment): https://github.com/HelTecAutomation/ASR650x-Arduino
HTCC-AM01 Pin out Diagram
HTCC-AM01 Recommend Hardware Design
- Recommend schematic diagram
- Schematic and PCB package (Altium Designer)
- AutoCAD size drawing
- 3D module
Heltec LoRa Node Porducts Difference Table (Product Selection Table)
Frequently Asked Questions
Customer Test Report
CubeCell test: https://www.youtube.com/watch?v=lobNwqHLrag
- Test Info
-
LoRa 470MHz Max Output Power
LoRa 470~510MHz Receiving Status "S Parameters"
Maximum communication distance test
Low power test in sleep mode
